Dishwasher Repair
in Kitsap County, WA

Standing water in the bottom, dishes that come out gritty, or a cycle that quits halfway are the dishwasher problems we hear about most. Bremerton Rabbit Appliance repairs built-in dishwashers across Kitsap County, 7 days a week, 8 AM to 7 PM, with same-day visits when you call early and one written price after the diagnosis.

✓ Open 7 days a week, 8 AM – 7 PM✓ Same-day visits when you call early✓ One written price after diagnosis — approved by you first

Get a Visit on the Books

Tell us what the machine is doing. We call back with a window and get you on today's route when the clock allows.

$20 OFF code HOP20 rides along with this request — it comes off any completed repair.

We diagnose first, then hand you one written price. Nothing is installed until you approve it.

7 days a week, 8 AM – 7 PM• Same-day visits when you call early• Written price after diagnosis, approved by you• Warranty on parts and labor, on the invoice
How it runs

Dishwasher Repair, Diagnosed Before It's Quoted

A dishwasher does four jobs in order: fill, wash, drain, dry. Our diagnosis follows the same order. We check the supply and the inlet valve, then the wash pump, the spray arms and the filter, then the drain pump and the hose to the sink, and finally the heater and the control. The finding is written down, the price is written down, and you approve it before any part is fitted. That sequence keeps us from replacing a pump on a machine whose real problem is a disposal plug that was never knocked out.

Water inlet valves are the part we replace most on Kitsap dishwashers, and well water is the reason. Homes on wells around outer Port Orchard, Manchester, Scandia and Lemolo push sand, iron and scale into the small screen inside the valve. Fills get shorter, the wash runs weak, and eventually the machine throws a fill error or stalls. On city water the same valve simply wears out and either stops opening or will not close and drips into the tub between cycles. We clean screens, test the solenoid, and replace the valve only when it has failed.

Drain problems are the second big category, and most are not the dishwasher's fault. A drain hose that loops below the counter traps water; an air gap on the sink that has never been cleaned fills with debris; and a new garbage disposal installed with the dishwasher knockout still in place blocks the drain entirely. We check the whole drain path from the sump to the sink before we blame the pump. When the pump itself has failed, we usually carry the part and replace it on the spot.

Most dishwasher repairs are done in one visit from van stock: pumps, inlet valves, door latches, gaskets, heaters and thermal fuses for the major brands come with the technician. If a control board or a model-specific part must be ordered, you get a return date before we leave and the second visit is booked around your week, Saturdays and Sundays included. Parts and labor we install carry a warranty with the terms on your invoice. We do not do plumbing beyond the dishwasher connection, but we will tell you what we see under the sink.

Dishwasher holding water, leaking or quitting mid-cycle? Call (360) 717-8985, 7 days a week. Early calls across Kitsap usually get a same-day visit, and the price is in writing before work starts.
Spray arm and filter area inside a built-in dishwasher
Inside a built-in dishwasher — spray arm off, filter out, checking what the owner never sees.
Sound familiar?

What Owners Tell Us on the Phone

Water left in the bottom after the cycle

A drain pump blocked by a shard of glass, a fruit pit or a label is the first thing we look for, followed by a failed pump, a kinked drain hose, or a clogged air gap on the counter. A new garbage disposal with the knockout plug still in place causes this more often than people expect.

Won't fill, or fills very slowly

The water inlet valve is the usual fault. On well water its screen packs with sediment; on any water the solenoid wears out and the float switch can stick. We check pressure at the supply, clean or replace the valve, and watch a full fill before we call it done.

Dishes come out dirty or gritty

A filter that has not been cleaned, a wash pump that has lost pressure, spray arms clogged with scale, or a water heater set too low all leave food behind. Sometimes the detergent door is not opening. We check the wash system step by step and show you what we find.

Leaking from the door or underneath

A worn door gasket or a loose lower door seal leaks at the front. Underneath, a cracked pump housing, a split hose, a failed inlet valve, or a sump seal lets water onto the floor. We find the source rather than tightening everything and hoping.

Won't start or stops mid-cycle

A door latch that no longer tells the control the door is shut, a thermal fuse, a failed touchpad, or a control board that has lost a relay will all stop a cycle. We test the latch and the power path first, since those are the common and inexpensive causes.

No heat, dishes wet and cold at the end

The heating element or its relay has failed, or on newer machines the flow-through heater has. Without heat, a dishwasher cannot sanitize or dry, and some controls will stall the cycle waiting for temperature. We test the element with a meter rather than replacing it on suspicion.

Loud grinding, buzzing or humming

Grinding is usually something hard in the chopper or drain pump. Buzzing with no water movement is a pump that is jammed or has seized. A loud hum at the start of the cycle can be the inlet valve. We open the sump, clear it, and test the pumps under load.

Error code, blinking lights or a dead panel

Blinking lights and codes mean something different on every brand. A dead panel may be a tripped breaker, a blown thermal fuse, or a failed board. We read the code, then confirm with a meter, because the code points at a system rather than the exact part.

Town by town

Dishwasher Repair Across the Map

Dishwasher Repair in Bremerton

Bremerton kitchens from Manette to Union Hill and the newer Haddon townhomes are minutes from our East Bremerton base, and rental turnover keeps dishwasher latches and pumps on our daily list.

Dishwasher Repair in Silverdale

Quiet Bosch and KitchenAid machines in Silverdale's Ridgetop and Island Lake kitchens are a regular stop on our Highway 303 route, with flow-through heaters and boards on the van.

Dishwasher Repair in Port Orchard

Port Orchard reaches from city water on Bay Street to wells near Long Lake and Mullenix, and inlet valve work rises the farther out the dishwasher sits.

Dishwasher Repair in Poulsbo

Poulsbo dishwashers in Olhava-area subdivisions and older Liberty Bay houses give us an even split between electronic control faults and sediment-packed valves from well supplies.

Dishwasher Repair in Tracyton

Tracyton ramblers along Tracyton Beach Road and Bucklin Hill are a ten-minute hop from the shop, so a blocked drain pump can often be cleared the same afternoon.

Dishwasher Repair in Manchester

Manchester kitchens along Colchester Drive and Beach Drive are mostly on wells, and our planned routes out there carry inlet valves and screens for the common dishwasher brands.

From the routes

On the Job Across Kitsap

Meters first, opinions second. The crew doing what a visit actually pays for: measured diagnosis at the machine.

Spray arm and filter area inside a built-in dishwasher
Inside a built-in dishwasher — spray arm off, filter out, checking what the owner never sees.
Open built-in dishwasher with racks visible during a door and latch inspection
Door, latch and rack inspection on a kitchen built-in.
Dishwasher control panel showing a diagnostic readout
Panel readout mid-diagnostic — the machine tells its side of the story.
Stainless dishwasher in a kitchen before service
A kitchen stop — stainless front, wood floor, dog supervising off-frame.
Technician testing a French-door refrigerator with a multimeter
Refrigerator call — readings before any part gets named.
Technician metering an electric dryer in a garage laundry area
Garage-laundry dryer, meter on the heater circuit.
Range and oven control panel being checked during a service call
Oven controls going through their paces — locked panels after self-clean are a regular call.
Front-load dryer on a pedestal next to the matching washer
Pedestal laundry pair waiting its turn — tight quarters, standard work.
The longer answers

Down the Rabbit Hole, Carefully

There is water sitting in the bottom of the dishwasher. Is the pump dead?

Not always. The drain path has several places to fail, and the pump is only one of them. We look first for something in the sump: glass, a fruit pit, a produce sticker or a rubber band. Then we check the drain hose for a kink or a low loop, the air gap on the counter for debris, and the connection at the disposal, including the knockout plug if the disposal is newer than the dishwasher. Only after those are clear do we test the pump motor with a meter. If the pump has failed, we usually carry the part and replace it the same visit. You get a written finding and a written price before anything is replaced.

We are on a well and the dishwasher keeps throwing a fill error. What is happening?

Well water in outer Port Orchard, Manchester and parts of Poulsbo carries sand and iron that collect in the mesh screen inside the water inlet valve. Over months the fill gets shorter until the control gives up waiting and shows a fill error or stalls the cycle. The same grit wears the valve seat so it drips when closed. We clean the screen, test the solenoid, and replace the valve if it no longer opens or seals. If we are cleaning the same screen a second time, the better answer is a sediment filter on the supply, which a plumber can install. We will say that rather than repeat the same repair.

The dishwasher runs but the dishes come out dirty. What do you check?

We start with the filter and the spray arms, since a clogged filter or scale-blocked arm holes drop wash pressure more than any other single thing. Then we check that the water entering is hot, that the inlet valve is filling to the right level, and that the detergent door opens on time. If those are right, we test the wash pump for pressure and the heater for operation, because many controls will not run the main wash properly without reaching temperature. Hard water scale is common around Kitsap and builds up on arms and in the sump; a cleaning product and a filter habit fix much of it, and we will show you how.

The dishwasher is leaking onto the floor. Should I stop using it?

Yes, until it is looked at, because water under a dishwasher soaks the subfloor and the cabinet base and you may not see the damage for months. Shut the supply valve under the sink if you can reach it. Leaks at the front of the door are usually the gasket or the lower door seal and are a quick repair. Leaks underneath can be a split hose, a cracked pump housing, a failed inlet valve, or a sump seal, and we pull the machine to find the exact source. We dry the area and run a full cycle after the repair to confirm the floor stays dry before we leave.

How do you decide the price, and is it the same across Kitsap?

After the diagnosis, in writing, and only then. The technician tests the fill, wash, drain and control, writes down the finding, and gives you one price for the repair. You approve it before any part is installed. If you decline, we put the dishwasher back and leave. We do not quote over the phone because standing water alone can be a plug, a hose, a pump or a board, and they are different repairs. The approach is the same at every address we serve, from a Manette apartment to a Poulsbo hillside house. Mention code HOP20 when you call and $20 OFF comes off any completed repair, one per visit.

Owner habits

Four Things That Prevent the Next Call

Clean the filter every couple of weeks

Most dishwashers made in the last fifteen years have a removable filter in the floor of the tub. Twist it out, rinse it under the tap, and put it back. A clogged filter is the most common reason for dirty dishes and a sour smell, and it takes less than a minute to clean.

Run the hot tap before you start the cycle

The dishwasher fills with whatever is in the pipe, and in a Bremerton basement in January that is cold. Run the kitchen tap until it is hot, then start the cycle. The first fill will be hot, the detergent will dissolve, and the heater will not have to work as hard.

Keep the drain hose in a high loop

The drain hose should rise to the underside of the counter before it drops to the disposal or the air gap. Without that loop, dirty sink water siphons back into the tub. Check it after any work under the sink, since the loop often gets knocked loose.

Descale the spray arms and sump a few times a year

Kitsap water leaves scale in the small holes of the spray arms and on the heater. Pull the arms, clear the holes with a toothpick, and run an empty hot cycle with citric acid or a dishwasher cleaner. Clear arms restore wash pressure and keep the pump cooler.

Brands we see every week

BoschKitchenAidWhirlpoolGESamsungLGFrigidaireMaytagKenmoreElectroluxAmana
Quick ones

Fair Questions

Can you repair the dishwasher today?

Usually, if you call before early afternoon. We run 7 days a week, 8 AM to 7 PM, and a leaking dishwasher moves up the list. Calls later in the day get the first opening the next morning. We cannot promise same-day every time, but early callers rarely wait long.

Do you work on Bosch and other quieter European-style dishwashers?

Yes. Bosch and similar machines are common in newer Silverdale, Poulsbo and McCormick Woods kitchens. They have a flow-through heater and a different pump layout from older American machines, and we carry the common parts for them.

Is a dishwasher that smells bad a repair problem?

Usually not. Food caught in the filter and sump, and a drain hose that holds water, cause most odors. Clean the filter, run a hot cycle with a dishwasher cleaner, and check the hose has a high loop. If the smell stays after that, the sump may be holding water and we will look.

I installed a new disposal and now the dishwasher won't drain. Related?

Very likely. New disposals ship with a knockout plug in the dishwasher inlet, and if it was not punched out the dishwasher has nowhere to drain. It is a quick fix. We check it first on any drain call where the disposal looks new.

Do you install dishwashers or do the plumbing under the sink?

We repair dishwashers; we do not do new installs or house plumbing. If the supply valve under the sink or the drain plumbing needs work, a plumber handles that. Once the dishwasher is connected, we are glad to service it for as long as it runs.

$20 OFFANY COMPLETED REPAIR
Code HOP20 — say it on the phone or let the form carry it for you.

Comes off the completed repair. One per visit; doesn't stack with other offers. No expiration games, it's just the standing deal, seven days a week.

Claim It — (360) 717-8985
From the notebook

Read Next

 Troubleshooting · 6 min read

Dishwasher Not Cleaning Dishes in Bremerton: Where to Look First

Dishes coming out gritty or filmy after a full cycle? Start with the spray arms and the filter, then check water temperature, detergent dosing for soft Kitsap water, and loading. This guide for Bremerton and Silverdale homes explains which fixes are yours and which need a technician.

Read the guide →
 Troubleshooting · 6 min read

Dishwasher Not Draining in Kitsap County: Safe Checks Before You Call

Standing water after the cycle usually means a blocked sump, a kinked or unlooped drain hose, a clogged air gap, or a disposal knockout that was never removed. Work through the safe checks in order, with notes for well-water homes around Manchester, and know when the pump needs a meter.

Read the guide →
 Troubleshooting · 6 min read

Dryer Not Heating in Bremerton: What to Check First

A dryer that tumbles but never warms up is one of the most common calls we take in Bremerton. The cause is usually a blocked vent, a blown thermal fuse, or a failed element, and the order you check them matters. Here is what to look at safely before you call.

Read the guide →
 Liberty Bay, Poulsbo

The Poulsbo Dishwasher That Would Not Drain on a Sunday

A dishwasher above Liberty Bay held an inch of dirty water on a Sunday morning with company due that evening. A same-day weekend visit found broken glass packed into the sump and a drain hose lying flat under the sink.

Read the case →
 Tracyton

The Tracyton In-Door Ice Maker That Went Quiet

An in-door ice maker on a French-door refrigerator in a Tracyton waterfront house simply stopped, no noise and no puddle. The fill tube had frozen solid because the inlet valve passed only a trickle, and the trickle froze before it reached the mold.

Read the case →

Book a dishwasher repair visit

Open every day of the week. Call before early afternoon and we can usually fit you in today.