Troubleshooting · 6 min read

Gas Range Burner Won't Light: What Kitsap Homeowners Can Check

Gas range burner clicking but not lighting? Safe checks for wet igniters and clogged ports, propane notes, what never to do, and when to call in Kitsap.

7 days a week, 8 AM – 7 PM• Same-day visits when you call early• Written price after diagnosis, approved by you• Warranty on parts and labor, on the invoice
Range and oven control panel being checked during a service call
Oven controls going through their paces — locked panels after self-clean are a regular call.

Click, click, click, and no flame. A gas cooktop burner that sparks but never lights, or one that does not spark at all, is a common call from Poulsbo kitchens, especially in the older hillside and waterfront houses above Liberty Bay where ranges have been in service for decades. Sometimes the fix is a paper towel and ten minutes of patience. Sometimes it is a spark module or a gas valve, which is our job and not yours.

This article covers the usual reasons a surface burner refuses to light, the checks that are safe for any homeowner, and the firm line we draw around anything that carries gas. One rule comes before everything else. If you smell gas, do not keep clicking the knob, do not flip a light switch, and do not hunt for the source. Leave the house and call your gas utility or propane supplier from outside.

Start with the obvious: is the burner wet?

The most common cause of a burner that clicks but will not light in Poulsbo is water. After a boil-over, a deep scrub, or a dishwasher run on the grates and caps, moisture sits in the burner head and around the ceramic igniter electrode. Water shorts the spark to ground before it can jump to the gas, so you get a weak click or a steady click and nothing else. In the dampest part of our service map, the fix is often just dry parts and a little time.

  • Lift off the grate, the burner cap, and the burner head and set them on a towel
  • Dry everything, including the igniter electrode, and let it air dry for a half hour
  • Reassemble so the cap sits flat and the head is seated squarely, then try again

Clogged ports and a cap that sits crooked

Each burner head has a ring of small ports where the gas comes out. Grease and the residue from a hard cleaning can block some of them, which produces a lazy yellow flame on one side, a flame that will not travel all the way around, or no ignition at all. A cap put back a few degrees off center causes the same thing. With the head removed from the range, clear ports with a wooden toothpick or a soft brush, never a metal pin, because enlarging a port changes the flame. Do not poke anything into the brass gas orifice the head sits on, and do not try to unscrew it; if it looks dirty, leave it for the technician.

No click at all: the spark module and the switch

If you turn the knob and hear nothing from any burner, the spark module is the likely cause, or the range has lost power. The module sends a high-voltage pulse to each electrode, and when it fails every burner usually goes quiet at once. If only one burner is silent, the problem is more often that burner's spark switch behind the knob or a cracked electrode. First make sure the range is plugged in and the breaker is on, because a gas range still needs electricity to spark. If one burner clicks constantly with the knob off, unplug the range to stop it and call.

Propane versus natural gas

Poulsbo has a mix of natural gas service in town and propane tanks out toward Scandia and Lemolo. The two fuels burn differently, and a range has to be set up for the one it is on. A range converted incorrectly, or never converted, lights poorly, burns with tall yellow flames, soots pans, or will not stay lit on low. Propane homes have one more variable: a nearly empty tank or a regulator icing up on a cold morning starves the range. If every burner is weak and the furnace is struggling too, call your propane supplier first. If the range alone is the problem, that is where we come in.

What never to do with a gas range

If the burner lights but the flame is tall, yellow, or lifting off the ports, turn it off and stop using it. That pattern means the air and gas mix is wrong, and it produces carbon monoxide along with soot. It is not an emergency the way a gas smell is, but it is a reason to use a different burner and have it looked at soon rather than next month.

  • Never try to light a burner with a match after it has been clicking for a while
  • Never remove, bend, or adjust the gas orifice, the valve, or the manifold
  • Never disconnect the flexible gas connector behind the range to look at it
  • Never spray cleaner into the burner base while the range is on

When to call Rabbit Appliance

Call us when the burner is dry and clean and still will not light, when there is no click on any burner with the range powered, when one burner clicks nonstop, or when flames look wrong. Rabbit Appliance serves Poulsbo, Keyport, and the Olhava area seven days a week from our East Bremerton base, and we carry spark modules, electrodes, and switches for the common brands. We do not run gas piping or do house wiring; if the trouble is upstream of the range, we will tell you who to call.

Bottom line: Most gas burners that will not light are wet, dirty, or reassembled crooked, and a careful dry-and-clean fixes them. A range with no click anywhere, a burner that clicks nonstop, or a yellow flame needs a technician. Gas valves, orifices, and connectors are never owner parts, and a gas smell means leave the house first and ask questions later.
Asked often

Questions on This Topic

The burner clicks for a while and then lights with a small pop. Is that dangerous?

A delayed light with a pop means gas built up for a few seconds before the spark caught it. Once in a while after cleaning, it is just a damp electrode. Every time, it points to a weak spark, a crooked cap, or blocked ports, and the pop will get bigger. Clean and dry the burner first; if it keeps happening, stop using that burner and have it checked.

Can I replace the igniter electrode on my range myself?

We would rather you did not. The electrode itself is harmless, but reaching it means working next to the burner valve and orifice, and the wiring runs under the cooktop near the gas manifold. A slipped tool or a loosened fitting there is a gas problem, not an electrical one. Replacing electrodes and spark modules is a quick visit for our technicians, and the parts are usually on the van.

Does Rabbit Appliance come out to Poulsbo and the north end of the county?

Yes. Poulsbo, Keyport, Lemolo, and the Olhava area are a regular part of our route up Highway 3 from East Bremerton, seven days a week. Call before early afternoon and we can often come out the same day; later calls get the first opening the next morning. Have the brand and model handy, and tell us whether the range is on natural gas or propane.

Burner still not lighting? Call Bremerton Rabbit Appliance at (360) 717-8985. We serve Poulsbo and all of Kitsap seven days a week, with same-day visits when you call early. (360) 717-8985
From the notebook

Read Next

 Troubleshooting · 6 min read

Oven Not Heating in Bremerton: What to Check Before You Call

An oven that lights up but never gets hot usually comes down to the bake element, a weak gas igniter, the temperature sensor, or a fuse tripped by self-clean. Here is how Bremerton homeowners can narrow it down without tools, and where it becomes a meter job.

Read the guide →
 Troubleshooting · 6 min read

Oven Temperature Running Hot or Cold: A Kitsap Troubleshooting Guide

Burnt bottoms and underdone centers often trace back to oven temperature. Learn how an oven cycles, how to run a thermometer test, when the calibration offset is the right fix, and when a drifting sensor, convection fan, or leaking door gasket means a Port Orchard service call.

Read the guide →
 Brand Guide · 6 min read

LG Washer & Dryer Repair in Bremerton: Codes, Boots and Heat

LG laundry pairs are quiet, efficient and very common in Bremerton and up through Poulsbo. When they fail, they tell you with a code. This guide decodes the ones that matter, explains what a direct-drive motor does and does not break, and lists the owner checks worth doing first.

Read the guide →
 McCormick Woods, Port Orchard

The McCormick Woods Wall Oven Locked After Self-Clean

A built-in electric wall oven in a McCormick Woods home ran self-clean the evening before a dinner, then refused to unlock or heat. The latch motor had stalled and the thermal fuse behind the control had opened from the heat.

Read the case →
 Liberty Bay, Poulsbo

The Poulsbo Dishwasher That Would Not Drain on a Sunday

A dishwasher above Liberty Bay held an inch of dirty water on a Sunday morning with company due that evening. A same-day weekend visit found broken glass packed into the sump and a drain hose lying flat under the sink.

Read the case →

Want it fixed instead of researched?

Call any day, 8 AM to 7 PM. Early calls usually land a same-day visit.